HC-0803
8 Fused
10 Amp Relays
The HC-0803, interposing device, interfaces between control panels and door locks, lighting circuits, HVAC, etc. A red status LED is provided for each relay. Relays are UL recognized.
Models:
HC-0803 - 10 Amp
HC-0803-5 - 5 Amp
Additional Information
HC-0695
8 Relay Utility - Socketed - 10 Amp
HC-0724
8 Relay Utility 30 Amp
The HC-0695 and HC-0724, interposing devices, interface between control panels and door locks, lighting circuits, HVAC, etc.
Additional Information
HC-0801 / HC-0604
2 DPDT 2 AMP RELAYS - 8 SPST REED RELAYS
The HC-0801, interposing devices, interfaces between control panels and low amperage field devices. A green diagnostic status LED is provided for each relay. Relay coils and contact points are available on both screw terminals and ribbon connectors.
The HC-0604 interfaces between control panels and low amperage controlled field devices A RED diagnostic / status LED is provided for each relay.
Additional Information
HC-0701
Remote Panel Controller
The HC-0701 communicates with an HC-0682 System Controller, or a Personal Computer, via a single twisted pair shielded RS-485 data cable. Multiple HC-0701 modules may be used on control panels with greater than 128 I/O.
Note: LED supervision boards, HC-0804 and HC-0806. The HC-701 cannot be used in combination with the Remote Panel Controller.
Additional Information
HC-0731
16 Point Adapter
The HC-0731 converts sixteen 22 to 12 AWG field device conductors to 26 AWG ribbon cable and provides circuit pads for LEDs, resistors, diodes and power capacitors to modify or customize the sixteen circuits.
Options:
Diodes, resistors, LEDs, etc. can be installed to provide lamp testing, status LEDs, or other special applications. Please call for special assemblies
Additional Information
HC-0639 / HC-0476
Adapters
The HC-0639 converts fifty 22 to 14 AWG field device conductors to 26 AWG ribbon cable.
The HC-0476 converts fifty 22 to 14 AWG field device conductors to 25 pair telephone type cable.
Additional Information
HC-0675
10 Point Adapter
The HC-0675 converts ten 22 to 14 AWG field device conductors to 26 AWG ribbon cable.
Additional Information
HC-0673
50 Point Resistor /
Diode Adapter
The HC-0675 converts ten 22 to 14 AWG field device conductors to 26 AWG ribbon cable.
The HC-0673 converts fifty 22 to 14 AWG field device conductors to 26 AWG ribbon cable and provides either in-line resistors or diodes.
Models:
HC-0673-R - 680 ohm 1/4 watt resistors (current limiting at 12VDC for 2V LED)
HC-0673-D - 1N4004 diodes
Additional Information
HC-0815A / HC-0815B
50 Pin Inline Adapter - Diode
The HC-0815A adds an inline diode to forty-eight circuits.
The HC-0815B adds an inline diode to forty-eight circuits with a common anode connection prior to each.
Additional Information
HC-0815c / HC-0815d
50 Pin Inline Adapter - Driver
The HC-0815C adds an inline driver to forty-eight circuits.
The HC-0815D adds an inline 680 ohm resister to forty-eight circuits.
Additional Information
HC-0815E / HC-0815F
50 Pin Inline Adapter - 120 OHM Resistor
The HC-0815E adds an inline 120 ohm resistor to forty-eight circuits.
The HC-0815F adds a common cathode connection to forty-eight circuits.
Additional Information
HC-0815g
50 Pin Inline Adapter - Diode Plus Common Cathode
The HC-0815G adds an inline diode to forty-eight circuits with a common cathode connection after each.
Additional Information
HC-0642
Flasher
The HC-0642 provides a half second flash rate output.
Additional Information
HC-0804AA / HC-0804AB
LED Supervision Motherboard and sisterboard
LED Supervision Motherboard and sisterboard.
The HC-0804 AA functions in conjunction with the HC-0806 LED Supervision Daughterboard. Forty-eight status display inputs are adapted for supervision of, and output to, the LEDs. Up to four HC-0804AB sisterboards share an HC-0806.
Additional Information
HC-0806
LED Supervision Daughterboard
The HC-0806 supervises up to 240 LEDs for short or open condition. Failures are detected an in either the LED's on or off state. The supervision circuit automatically resets when a failure is corrected or no longer detected.. Short (red), Latch (yellow), Open (red) and Power (green) status LEDs are provided. The Latch yellow LED captures an intermittent failure detection and must be reset by a technician.
Additional Information
HC-0828
50 Point Tester
The HC-0828 provides a convenient means to test fifty
separate circuits. Each circuit has a status LED and an
on-off switch. A red LED indicates when the circuit is low.
A switch is provided to ground the circuit.